Search the Community
Showing results for tags 'delay() signal'.
This method demonstrates how to apply time warping to a signal which can shorten the time between sample points while retaining the signal’s characteristic shape. This is useful for batch processes where batches may have different durations or for aligning data from multi-step processes with different durations. Note that this method is distinct from the more complex Dynamic Time Warping. The following example is based upon the Area A Compressor Power signal available in the Example Data. A single condition was created to capture each compressor run, as shown in the following image. Step 1: Specify a Time Normalization Factor The user uses the Formula tool to specifiy a time duration (scalar value), set to 4 hours for this example. The compressor power signal for each compressor run will be normalized to this time duration. There is no single correct value; the value needs to be shorter than the minimum time duration for all signals to be normalized. // User specified time duration (scalar value). 4 hours Step 2: Create the Normalized Condition Use Formula to create the normalized Compressor Run condition based on the user-specified time normalization factor. This condition will be used later when the calculated signal delay is used for normalization. $CompressorRuns.afterStart($nF) Step 3: Calculate the Run Duration Use the Signal from Condition tool to calculate the duration for each compressor run. This value will be used later for determining the calculated signal delay applied to each compressor run. Step 4: Calculate the Elapsed Time During Each Run Use the Formula tool to calculate the elapsed time during each compressor run. This value will be used later for determining the calculated signal delay applied to each compressor run. timeSince($CompressorRuns, 0.25min).convertUnits('h') Step 5: Calculate the Signal Delay Factor Needed for Time Warping Each sample (timestamp) for compressor power will be shifted to the left by a calculated amount to time warp the power signal from its original time period (Compressor Runs) to the normalized time period (Compressor Runs Normalized). The first sample point in each run will have no delay, and the last sample point will have the greatest delay. For example, if the original time period is 10 hours and we are normalizing to a time period of 4 hours, then the last sample point in the run will be shifted to the left by 6 hours (Delay Factor = -6 hrs). // This Formula first creates a signal with a value of 0 (default delay), then splice in the calculated delay during each compressor run. 0.toSignal(0.25min).convertUnits('hr').splice($ElapsedTime*($nF/$RunDuration-1),$CompressorRuns) At this point we zoom in to a single compressor run and use the Capsule Time view to better visualize the results of our intermediate calculations. For this compressor run lasting 10.9 hours, the Compressor Run Elapsed Time finishes at the correct value (10.9 hours) and the Delay Factor correctly decreases from 0 hours (beginning of run) to -6.9 hours (end of run). Step 6: Apply the Signal Delay to Time Warp the Signal Now that the appropriate delay factor is calculated for each sample point during the compressor runs, we apply it to the Area A Compressor Power signal using the delay() function in Formula. This generates the time warped signal called Compressor Power Normalized. $CompressorPower.delay($delayFactor,24h).within($CompressorRunsN) When applying the signal delay, we are required to specify a maximum delay. This is important for the Seeq calculations going on in the background, so that the queries know how far back and forward to go when requesting input data. The maximum delay also provides a convenient way for the user to limit the applied delay, if they have some reason to do so. In our case, we just want the chosen value to be longer than the longest expected compressor run duration. Results Now that the compressor power signal has been normalized, Capsule Time view gives a nice comparison of the power signal behavior across the 3 runs contained in the Display Range:
FAQ: I have a condition for events of variable duration. I would like to create a new condition that comprises the first third of the time (or 4th, or 10th) of the original condition. Solution: A stepwise approach can be taken to achieve this functionality. 1. Begin with your condition loaded in the display pane. 2. Create a new Signal using Signal from Condition that calculates the total duration of each of your event capsules, interpolated as a step signal. 3. Create a new signal that is your total event duration multiplied by the proportion of the event that you would like to capture. e.g. for the first 1/3 of the event, divide your total duration signal by 3, as shown below. 4. Create an arbitrary discrete signal with a sample at the start of each of your event capsules. 5. Shift the arbitrary discrete signal in time by the value of your signal calculated in step 3. In this example, the 1/3 duration signal. Note, depending on your version of Seeq, the function to do this may be called move() or delay(). 6. Use the toCapsules() function in Formula to create a tiny (zero duration) capsule at each of your shifted, discrete samples. 7. Join the start of your original condition with the capsules created in step 6 using the composite condition tool.